This instruction cannot be a detailed description of all sizes and measurements of the material. For self-production of bird feeders, everything that you can find on your site is suitable. However, the assembly steps themselves will be explained in as much detail as possible. The project was originally designed to use the cheapest and most affordable materials, without using screws or nails, but only glue.

Materials

An example list that can be changed at your discretion:

1. Used wooden pallet or wood.
2. Saw.
3. A sander or sandpaper with a wooden block.
4. Polymerizing gorilla glue or self-tapping screws.
5. Tape measure and pen
6. Putty on wood.
7. Clamp.

How to use gorilla glue

The project will be made only using gorilla glue and scabbers, without the use of screws or nails. Therefore, you should first tell us how to apply it in practice:

1. Clean the wood from dirt and dust with a brush and sandpaper.
2. Moisten the workpiece on both sides with water.
3. Apply glue to the raw wood.
4. Fix the bars together with clamps.
5. Wait until the structure dries (after 1-2 hours — 80%, after 24 hours — 100%). I think a little more than 1 hour is enough.


Disassembling the pallet

1. Free the pallet from nails, otherwise the saw teeth will become unusable.
2. Spread the boards on the floor.
3. Cut them to size with any saw.

Alternatively, mark the base of the pallet in a place where there are no nails and cut out the necessary parts.


Preparation of wood for the base of the feeder and manufacture

To do this, use the pallet base boards, as they are the thickest in the structure. Pre-determine the size of the feeder and use a tape measure, pencil or pen and a saw to cut the pieces at an angle of 90 degrees.


Supports for the base

Make 2 supports for the bottom of the base. Wood clippings or pallet boards are suitable. When measuring, try to stick to right angles.

Grinding of the material

The stage is optional if you want to get a rustic look or when the pallets are smooth and without dirt frozen on them. Otherwise, you can catch a drift when using a feeder.

Suitable for grinding and:

1. Grinding machine;
2. sandpaper fixed on a wooden bar.

Manufacturing of the base

1. Assemble the prepared parts of the base.
2. Install the boards without gaps.
3. Press them together with clamps.
4. Wait for them to stick.


We make the “walls” of the feeder

It's not a blank wall, but it will keep the feed from spilling out of the structure and getting the floor wet. The element consists of 4 interconnected bars. Measure the width of the base of the feeder with a tape measure, while taking into account that the horizontal bars will be located between the vertical ones, so leave room for the latter.

1. Apply glue to the base, attach the lower parts of the “wall” and press them with clamps.
2. Make vertical racks with a height of 200 mm.
3. Apply glue to them and clamp them with a clamp.
4. After the glue has solidified, cut off the excess material that has protruded with a knife, as it expands approximately 1 to 3.


Roof

Support

Use any suitable piece of wood, but it should be wide enough to tie the narrow boards off the pallet. Connect the latter to each other at the ends with glue and fix them. Or find a piece of suitable timber.

Making a roof

1. Select the necessary pieces of wood. You will need 2 elements, each of which consists of 3 slats.
2. Connect them with glue.
3. Fix with clamps.
4. Sand the workpiece.

Roof support element

1. The plank should be thick enough so that the prepared roof can be firmly installed and secured on it.
2. For better reliability, it needs to be mowed.
3. Make the markup with a pencil and a pencil (or something similar), and then cut off the resulting elements.

Creating a roof frame

It remains to connect all the elements of the roof together, after which the feeder will not be flooded with precipitation and the feed will not get wet.

1. Fix the 4 roof support elements on the central beam with glue, fixing them with a clamp. Do this not flush, but leaving some overhang.
2. Attach the resulting structure to the vertical slats of the walls.
3. After the glue dries, remove the excess with a sharp knife.


Gluing elements

1. Apply glue to the roof at the places where the support is installed.
2. Attach the bars and press them with clamps.

Seal the holes

Use a wood putty that dries quickly. The car will not work precisely because of this.

Grinding

Sand the applied putty with sandpaper after 15-30 minutes. Otherwise, she will “reach out” for her. It is easiest to grind with a special machine, although there will be more dust from it.

Wood protection

Use teak oil or whatever is at hand. Pre-remove the dust from the surface. Apply at least 2 coats.

Additions

To make your feathered friends feel like “emperors“ in their ”palace", add everything necessary for feeding to it. Stepping back a bit from the topic, we want to tell you about a profitable financial offer from an online casino. Only 300 people can get 1go casino no deposit bonus for registration. Follow the link and read the instructions for receiving it.